Grid view List view 10K BIAS POT MIL STYLEMil style, linear taper, 2 watt, 10% tol. Carbon potentiometer. Short 5/8″ lt. slotted shaft with locking collar and all mounting hardware to fit 3/8″ dia. hole. Nice upgrade! New Production (Made in Canada). $15.00 View Product 2 LUG TERMINAL STRIPCadmium plated lugs on Phenolic strip. Small style: 1/4″ spacing with (.096″) # 3 screw hole. Large style: 3/8″ spacing with (.140″) # 4 thru # 6 screw hole. (Non-Grounded) “Sold as each” View Product 2 Terminal Binding PostGold plated (2) terminal binding post mounted on a brown Phenolic strip. Binding posts have standard 3/4 inch spacing and accept (4mm) banana jacks or bare wire connections up to 10 gauge. Includes (1) Red & (1) Black jacks, mounting… $12.50 View Product 3 LUG TERMINAL STRIP3 Lug terminal strip (center ground) cadmium plated lugs on Phenolic strip. Small style ¼” spacing with (.096″) # 3 screw hole. Large style 3/8” spacing with (.140″) # 4 thru # 6 screw hole. (Sold as each) View Product 3 Terminal Binding PostsGold plated (3) terminal binding posts mounted on a brown Phenolic strip. Accepts standard (4mm) banana jacks or bare wire up to 10 gauge. Includes (2) Red & (1) Black jacks, mounting strip, terminal strip and hardware. Fits: SCA-35, ST-70, MK III… $12.50 View Product 5 Lug Strip(Center ground) cadmium plated lugs on Phenolic strip. 3/8″ spacing with #6 screw hole. $2.00 View Product 5 Lug Strip ST-35(Center ground) Cadmium plated lugs on phenolic strip. 3/8″ spacing with #6 screw hole. Note: 30 degree angled lugs for (ST-35) & (SCA-35). $2.50 View Product 7 Pin Tube SocketsMiniature 7 pin tube sockets for 12X4 rectifier tube. Select (CER) for Ceramic or (MIC) for the (NOS) Micanol. The (CER) version is a top/bottom chassis mount style whereas the (MIC) version is a fixed bottom chassis mount only. Each… View Product 8 PIN OCTAL SOCKETNew production “Celenex” octal socket. Tin plated pins, bottom mount style. Fits 1.125” chassis hole. Mounting centers are 1.50”. Fits new & original Dynakit/Dynaco products. Note: This is the standard socket provided with our MK III, MK IV & ST-70… $4.00 View Product Out of Stock 8 PIN OCTAL SOCKETMicanol n.o.s. chassis mount, cadium plated pins, flanged bottom mount style. Fits 1 1/8″ hole with 1 1/2″ mount hole centers with (4) grounding lugs . Cinch mfg. Quality heavy-duty construction. $4.75 View Product 9 Pin Ceramic SocketPC mount, nickel plated pins. Circuit board mount style. Fits 13/16″ dia. hole. mounting. $2.50 View Product 9 PIN CERAMIC SOCKETChassis mount, cadium plated pins, top/bottom circuit board mount style. Fits 13/16″ to 7/8″ dia. hole. Note: orientation of pins with respect to mounting flange is non-standard, China mfg. $2.25 View Product 9 PIN CERAMIC SOCKETChassis mount, cadium plated pins, top circuit board mount style. Fits 13/16″ to 7/8″ dia. hole. Note: orientation of pins with respect to mounting flange is standard. Nice Quality… China mfg. $3.25 View Product 9 PIN CERAMIC SOCKETPC mount, gold plated pins, circuit board mount style. Fits 13/16″ dia. mounting, China mfg. $3.00 View Product 9 Pin Micalex SocketChassis mount, nickel plated pins. Top mount style. Fits 3/4″ hole. Imported. $3.00 View Product 9 Pin Micalex SocketPC mount, nickel plated pins. Circuit board mount style. Fits 13/16″ dia. mounting. $3.00 View Product 9 PIN Micanol SocketChassis mount, cadium plated pins, top mount style. Fits 3/4″ hole. Cinch style, USA mfg. $4.50 View Product 9 PIN SOCKET ADAPTERPermits the use of the 6GH8A Tube in place of the 7199 tube. This low profile high quality socket adapter re-arranges the pin connections to permit use of the 6GH8A tube while retaining the original DYNA Circuitry. Includes ceramic socket,… $20.00 View Product Out of Stock A 470 Output Transformer35 watts, 4300 ohm c.t. For mounting and wiring details, refer to dimensional/electrical schematic. Exact drop-in replacement for Dynakit ST-70 and Mark IV amplifiers. $180.00 View Product Out of Stock A-431 Output Transformer60 watts, 4300 ohm c.t. For mounting and wiring details, refer to dimensional/electrical schematic. Exact drop-in replacement for Dynakit MKIII amplifier. $250.00 View Product Out of Stock AC PANEL OUTLETS NOSReplacement Non-polarized 125 vac 15 amp panel mount power outlets. Very similar to the original Dynaco black plastic AC outlets found on the SCA-35, PAS and FM1-FM3 models. May also fit “other” vintage gear of same era. Fits minimum chassis… $10.00 View Product AC Snap-in ReceptacleOptional AC Polarized plug receptacle for the New PAS or SCA Chassis. Snap-in style mount (2) conductor with solder type lugs. Rating: 15 Amp @ 125 VAC. … $2.50 View Product Bias Balance Control KitThe Dynakit BBCU-1, Bias Balance Control Upgrade is a simple and effective circuit upgrade for equalizing the bias current between each pair of output tubes. Designed specifically for the original or new Dynakit ST-70, Mark II/III and MKIV amplifiers. The… View Product BIAS RESISTOR….MARK III11.2 ohm 1% precision wire wound non-inductive bias resistor. Sold as each. $6.00 View Product BIAS RESISTOR….MARK IV13.5 ohm 1% precision wire wound non-inductive bias resistor. Sold as each. $6.00 View Product BIAS RESISTOR….ST-7015.6 ohm 1% precision wire wound non-inductive bias resistor. Sold as Each. $6.00 View Product Black Rubber FeetVery similar to the original dynakit push-on rubber feet.(9/16″ o.d. x 1/8″ ht) fits hole size of .180″ – .288″ dia. Sold in sets of (4) only. $3.00 View Product Black Rubber Feet (Large)Large tapered profile SBR rubber feet. 1″ dia. x 27/32″ height. Includes 10/32 mounting hardware. Sold in sets of (4). Note: Will not fit the MK IV amplifier due to location of choke. $10.00 View Product Black Rubber Feet (Med)(3/4″ OD x 9/16″ Ht) Includes 10-32 mounting hardware requiring a 3/16″ to 1/4″ Dia. mounting hole. Fits most Dynaco tube amps, preamps and tuners. Sold in sets of (4) only. Note: Will not fit the MK IV model amplifier… $7.50 View Product BushingsBlack plastic hole, snap-in wire insulating bushings. Fits 5/8″ dia. hole. Typically used for transformer leads routing through chassis. Sold in sets of (4) only. $1.50 View Product C-354 CHOKED.C. filter choke. 1.75 Henries, 200ma. DC current, 62 ohms, 400 vdc (max) 10% Tolerance. For mounting and wiring refer to dimensional & electrical schematic. Exact drop-in replacement for Dynakit ST-70, Mark III/IV. “New Shielded Design” Click here to see… View Product Out of Stock Sale Can Capacitor # 23222-6 “Dented”We have (2) multi-section can capacitors 30/20/20/20 uF @ 550/600 vdc. This is a popular choice for any number of the Dynaco/Dynakit amplifiers. The labels on both these capacitors are orientated to suit either the Dynaco/Dynakit ST-70 or MK IV… $75.00 $60.00 View Product Sale Can Capacitor # 284320-6 “Dented”We have one (1) multi-section can capacitor 80/40/30/20 uF @ 550/600 vdc. This is a popular choice for any number of the Dynaco/Dynakit amplifiers. The label on this capacitor is now orientated to suit the Dynaco/Dynakit MK III amplifier. We… $75.00 $60.00 View Product Sale Can Capacitor # 297227 (A) “Dented”We have one (1) multi-section can capacitor 60/40/20 uF @ 450 vdc & 100 uF @ 25 vdc. This is the exact value capacitor used in the original Dynaco or new production Dynakit ST-35 amplifier. This same value capacitor is… $50.00 $35.00 View Product Sale Can Capacitor # 297227 (B) “Dented”We have one (1) multi-section capacitor 60/40/20 uF @ 450 vdc & 100 uF @ 25 vdc. This is the exact value capacitor used in the original Dynaco or new production Dynakit ST-35 amplifier. This same value capacitor is also… $50.00 $25.00 View Product Centralab (5) Position Selector Switch.Centralab NOS (5) Position, Three deck rotary selector switch. A very nice quality switch originally made for H.H. Scott which appears to be intended for a PC type interface although each of the circuit traces can accept individual soldered lead… $5.00 View Product CERAMIC DISC CAPACITOR.02 uF x 100 vdc Various Brands. Sold as Each. $0.75 View Product CERAMIC DISC CAPACITOR.01 uF X1/Y1; Y5U 250 vac line rated ceramic capacitors. Vishay brand. Sold as Each. $2.00 View Product CERAMIC DISC CAPACITOR.01 uF x 100 vdc Various Brands. Sold as Each. $0.50 View Product Control HardwareControl Hardware: Multiple choice of selected hardware items for the mounting of your rotary controls and control knobs in your original or new Dynakit PAS/SCA chassis. CTL-HW-A Nylon (reducer) shoulder washer 3/8″ x 8mm. Use for mounting of metric type rotary… View Product 1 2 3 4 5